FreeBSD kernel usb device Code
ehcireg.h
Go to the documentation of this file.
1
/* $FreeBSD$ */
2
/*-
3
* SPDX-License-Identifier: BSD-2-Clause-NetBSD
4
*
5
* Copyright (c) 2001 The NetBSD Foundation, Inc.
6
* All rights reserved.
7
*
8
* This code is derived from software contributed to The NetBSD Foundation
9
* by Lennart Augustsson (lennart@augustsson.net).
10
*
11
* Redistribution and use in source and binary forms, with or without
12
* modification, are permitted provided that the following conditions
13
* are met:
14
* 1. Redistributions of source code must retain the above copyright
15
* notice, this list of conditions and the following disclaimer.
16
* 2. Redistributions in binary form must reproduce the above copyright
17
* notice, this list of conditions and the following disclaimer in the
18
* documentation and/or other materials provided with the distribution.
19
*
20
* THIS SOFTWARE IS PROVIDED BY THE NETBSD FOUNDATION, INC. AND CONTRIBUTORS
21
* ``AS IS'' AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED
22
* TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
23
* PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE FOUNDATION OR CONTRIBUTORS
24
* BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR
25
* CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
26
* SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS
27
* INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN
28
* CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
29
* ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
30
* POSSIBILITY OF SUCH DAMAGE.
31
*/
32
33
#ifndef _EHCIREG_H_
34
#define _EHCIREG_H_
35
36
/* PCI config registers */
37
#define PCI_CBMEM 0x10
/* configuration base MEM */
38
#define PCI_INTERFACE_EHCI 0x20
39
#define PCI_USBREV 0x60
/* RO USB protocol revision */
40
#define PCI_USB_REV_MASK 0xff
41
#define PCI_USB_REV_PRE_1_0 0x00
42
#define PCI_USB_REV_1_0 0x10
43
#define PCI_USB_REV_1_1 0x11
44
#define PCI_USB_REV_2_0 0x20
45
#define PCI_EHCI_FLADJ 0x61
/* RW Frame len adj, SOF=59488+6*fladj */
46
#define PCI_EHCI_PORTWAKECAP 0x62
/* RW Port wake caps (opt) */
47
48
/* EHCI Extended Capabilities */
49
#define EHCI_EC_LEGSUP 0x01
50
#define EHCI_EECP_NEXT(x) (((x) >> 8) & 0xff)
51
#define EHCI_EECP_ID(x) ((x) & 0xff)
52
53
/* Legacy support extended capability */
54
#define EHCI_LEGSUP_BIOS_SEM 0x02
55
#define EHCI_LEGSUP_OS_SEM 0x03
56
#define EHCI_LEGSUP_USBLEGCTLSTS 0x04
57
58
/* EHCI capability registers */
59
#define EHCI_CAPLEN_HCIVERSION 0x00
/* RO Capability register length
60
* (least-significant byte) and
61
* interface version number (two
62
* most significant)
63
*/
64
#define EHCI_CAPLENGTH(x) ((x) & 0xff)
65
#define EHCI_HCIVERSION(x) (((x) >> 16) & 0xffff)
66
#define EHCI_HCSPARAMS 0x04
/* RO Structural parameters */
67
#define EHCI_HCS_DEBUGPORT(x) (((x) >> 20) & 0xf)
68
#define EHCI_HCS_P_INDICATOR(x) ((x) & 0x10000)
69
#define EHCI_HCS_N_CC(x) (((x) >> 12) & 0xf)
/* # of companion ctlrs */
70
#define EHCI_HCS_N_PCC(x) (((x) >> 8) & 0xf)
/* # of ports per comp. */
71
#define EHCI_HCS_PPC(x) ((x) & 0x10)
/* port power control */
72
#define EHCI_HCS_N_PORTS(x) ((x) & 0xf)
/* # of ports */
73
#define EHCI_HCCPARAMS 0x08
/* RO Capability parameters */
74
#define EHCI_HCC_EECP(x) (((x) >> 8) & 0xff)
/* extended ports caps */
75
#define EHCI_HCC_IST(x) (((x) >> 4) & 0xf)
/* isoc sched threshold */
76
#define EHCI_HCC_ASPC(x) ((x) & 0x4)
/* async sched park cap */
77
#define EHCI_HCC_PFLF(x) ((x) & 0x2)
/* prog frame list flag */
78
#define EHCI_HCC_64BIT(x) ((x) & 0x1)
/* 64 bit address cap */
79
#define EHCI_HCSP_PORTROUTE 0x0c
/* RO Companion port route description */
80
81
/* EHCI operational registers. Offset given by EHCI_CAPLENGTH register */
82
#define EHCI_USBCMD 0x00
/* RO, RW, WO Command register */
83
#define EHCI_CMD_ITC_M 0x00ff0000
/* RW interrupt threshold ctrl */
84
#define EHCI_CMD_ITC_1 0x00010000
85
#define EHCI_CMD_ITC_2 0x00020000
86
#define EHCI_CMD_ITC_4 0x00040000
87
#define EHCI_CMD_ITC_8 0x00080000
88
#define EHCI_CMD_ITC_16 0x00100000
89
#define EHCI_CMD_ITC_32 0x00200000
90
#define EHCI_CMD_ITC_64 0x00400000
91
#define EHCI_CMD_ASPME 0x00000800
/* RW/RO async park enable */
92
#define EHCI_CMD_ASPMC 0x00000300
/* RW/RO async park count */
93
#define EHCI_CMD_LHCR 0x00000080
/* RW light host ctrl reset */
94
#define EHCI_CMD_IAAD 0x00000040
/* RW intr on async adv door
95
* bell */
96
#define EHCI_CMD_ASE 0x00000020
/* RW async sched enable */
97
#define EHCI_CMD_PSE 0x00000010
/* RW periodic sched enable */
98
#define EHCI_CMD_FLS_M 0x0000000c
/* RW/RO frame list size */
99
#define EHCI_CMD_FLS(x) (((x) >> 2) & 3)
/* RW/RO frame list size */
100
#define EHCI_CMD_HCRESET 0x00000002
/* RW reset */
101
#define EHCI_CMD_RS 0x00000001
/* RW run/stop */
102
#define EHCI_USBSTS 0x04
/* RO, RW, RWC Status register */
103
#define EHCI_STS_ASS 0x00008000
/* RO async sched status */
104
#define EHCI_STS_PSS 0x00004000
/* RO periodic sched status */
105
#define EHCI_STS_REC 0x00002000
/* RO reclamation */
106
#define EHCI_STS_HCH 0x00001000
/* RO host controller halted */
107
#define EHCI_STS_IAA 0x00000020
/* RWC interrupt on async adv */
108
#define EHCI_STS_HSE 0x00000010
/* RWC host system error */
109
#define EHCI_STS_FLR 0x00000008
/* RWC frame list rollover */
110
#define EHCI_STS_PCD 0x00000004
/* RWC port change detect */
111
#define EHCI_STS_ERRINT 0x00000002
/* RWC error interrupt */
112
#define EHCI_STS_INT 0x00000001
/* RWC interrupt */
113
#define EHCI_STS_INTRS(x) ((x) & 0x3f)
114
115
/*
116
* NOTE: the doorbell interrupt is enabled, but the doorbell is never
117
* used! SiS chipsets require this.
118
*/
119
#define EHCI_NORMAL_INTRS (EHCI_STS_IAA | EHCI_STS_HSE | \
120
EHCI_STS_PCD | EHCI_STS_ERRINT | EHCI_STS_INT)
121
122
#define EHCI_USBINTR 0x08
/* RW Interrupt register */
123
#define EHCI_INTR_IAAE 0x00000020
/* interrupt on async advance
124
* ena */
125
#define EHCI_INTR_HSEE 0x00000010
/* host system error ena */
126
#define EHCI_INTR_FLRE 0x00000008
/* frame list rollover ena */
127
#define EHCI_INTR_PCIE 0x00000004
/* port change ena */
128
#define EHCI_INTR_UEIE 0x00000002
/* USB error intr ena */
129
#define EHCI_INTR_UIE 0x00000001
/* USB intr ena */
130
131
#define EHCI_FRINDEX 0x0c
/* RW Frame Index register */
132
133
#define EHCI_CTRLDSSEGMENT 0x10
/* RW Control Data Structure Segment */
134
135
#define EHCI_PERIODICLISTBASE 0x14
/* RW Periodic List Base */
136
#define EHCI_ASYNCLISTADDR 0x18
/* RW Async List Base */
137
138
#define EHCI_CONFIGFLAG 0x40
/* RW Configure Flag register */
139
#define EHCI_CONF_CF 0x00000001
/* RW configure flag */
140
141
#define EHCI_PORTSC(n) (0x40+(4*(n)))
/* RO, RW, RWC Port Status reg */
142
#define EHCI_PS_WKOC_E 0x00400000
/* RW wake on over current ena */
143
#define EHCI_PS_WKDSCNNT_E 0x00200000
/* RW wake on disconnect ena */
144
#define EHCI_PS_WKCNNT_E 0x00100000
/* RW wake on connect ena */
145
#define EHCI_PS_PTC 0x000f0000
/* RW port test control */
146
#define EHCI_PS_PIC 0x0000c000
/* RW port indicator control */
147
#define EHCI_PS_PO 0x00002000
/* RW port owner */
148
#define EHCI_PS_PP 0x00001000
/* RW,RO port power */
149
#define EHCI_PS_LS 0x00000c00
/* RO line status */
150
#define EHCI_PS_IS_LOWSPEED(x) (((x) & EHCI_PS_LS) == 0x00000400)
151
#define EHCI_PS_PR 0x00000100
/* RW port reset */
152
#define EHCI_PS_SUSP 0x00000080
/* RW suspend */
153
#define EHCI_PS_FPR 0x00000040
/* RW force port resume */
154
#define EHCI_PS_OCC 0x00000020
/* RWC over current change */
155
#define EHCI_PS_OCA 0x00000010
/* RO over current active */
156
#define EHCI_PS_PEC 0x00000008
/* RWC port enable change */
157
#define EHCI_PS_PE 0x00000004
/* RW port enable */
158
#define EHCI_PS_CSC 0x00000002
/* RWC connect status change */
159
#define EHCI_PS_CS 0x00000001
/* RO connect status */
160
#define EHCI_PS_CLEAR (EHCI_PS_OCC | EHCI_PS_PEC | EHCI_PS_CSC)
161
162
#define EHCI_PORT_RESET_COMPLETE 2
/* ms */
163
164
/*
165
* Registers not covered by EHCI specification
166
*
167
*
168
* EHCI_USBMODE register offset is different for cores with LPM support,
169
* bits are equal
170
*/
171
#define EHCI_USBMODE_NOLPM 0x68
/* RW USB Device mode reg (no LPM) */
172
#define EHCI_USBMODE_LPM 0xC8
/* RW USB Device mode reg (LPM) */
173
#define EHCI_UM_CM 0x00000003
/* R/WO Controller Mode */
174
#define EHCI_UM_CM_IDLE 0x0
/* Idle */
175
#define EHCI_UM_CM_HOST 0x3
/* Host Controller */
176
#define EHCI_UM_ES 0x00000004
/* R/WO Endian Select */
177
#define EHCI_UM_ES_LE 0x0
/* Little-endian byte alignment */
178
#define EHCI_UM_ES_BE 0x4
/* Big-endian byte alignment */
179
#define EHCI_UM_SDIS 0x00000010
/* R/WO Stream Disable Mode */
180
181
/*
182
* Actual port speed bits depends on EHCI_HOSTC(n) registers presence,
183
* speed encoding is equal
184
*/
185
#define EHCI_HOSTC(n) (0x80+(4*(n)))
/* RO, RW Host mode control reg */
186
#define EHCI_HOSTC_PSPD_SHIFT 25
187
#define EHCI_HOSTC_PSPD_MASK 0x3
188
189
#define EHCI_PORTSC_PSPD_SHIFT 26
190
#define EHCI_PORTSC_PSPD_MASK 0x3
191
192
#define EHCI_PORT_SPEED_FULL 0
193
#define EHCI_PORT_SPEED_LOW 1
194
#define EHCI_PORT_SPEED_HIGH 2
195
#endif
/* _EHCIREG_H_ */
dev
usb
controller
ehcireg.h
Generated by
1.9.3